SUBSCRIBER & MEMBER LOGIN

Login, or register today to interact in our online community, comment on articles, receive our newsletter, manage your account online and more!

How to dress up your tubular track

Add paint and ballast to add realism to your rails
RELATED TOPICS: O GAUGE | TRACK
dress_up_tubular1
Frank pours the ballast between the rails, aiming to have the ballast flow naturally from the inside outward. His goals are to have the rails resting on the ballast and to make the ballast match the height of his ties.
Frank Knautz
dress_up_tubular2
Using a small, stiff brush, Frank taps the ballast down between the rails. You can also use the eraser end of a pencil or similar implement. By tamping the ballast down between the ties, he forces the ballast under the rails.
Frank Knautz
dress_up_tubular3
After smoothing out his initial application of ballast, Frank pours an additional layer of ballast along the sides of the roadbed to fill in the hollows and bring the ballast to the same height as the ties.
Frank Knautz
dress_up_tubular4
In addition to adding extra wood ties, Frank places wood plugs into the ends of the hollow metal ties. Note how the ballast surrounds the tie and holds it in place – as it would in the real world. The emphasis when ballasting is around the tie and under the rails.
Frank Knautz
dress_up_tubular5
When he is satisfied with the placement of his ballast, Frank secures the granules by applying a mixture of equal parts water and common white household glue in a hair dye applicator. He adds a drop of liquid dishwashing soap to break the surface tension of the water and allow the glue to flow into the ballast easier. Frank also tints the mixture by adding drops of Woodland Scenics no. C1222 burnt umber until the glue and water mix resembles chocolate milk.
Frank Knautz
dress_up_tubular6
Using the applicator, Frank applies his diluted and tinted glue to all visible areas. He finds it best to apply a few drops at the intersection of the rails and ties, let it seep in, and then reapply. Frank makes several applications, adding a few more drops each time. This gradual method allows the bottom layer of ballast to fully set. Afterwards, he secures the outer slope of ballast with the same glue mixture. As you can see, it’s messy and the words “What have I done?” may cross your mind. Relax, Frank says, once the glue has dried, it will look great.
Frank Knautz
dress_up_tubular7
With the ballast firmly glued in place, Franks applies a mixture of equal amounts of burnt umber and water, liberally slopped on with a loose brush. After a few passes, Frank makes one final coat, this time using a mixture of India ink and ethyl alcohol. The alcohol evaporates, leaving a film of black over the top. The photo shows a before and after – the area at the lower left is freshly laid ballast; the area at upper right has been tinted.
Frank Knautz
There are many track choices available to the O gauge hobbyist, but for the traditional enthusiast Lionel tubular track has great appeal. This is the track we grew up with, and for many of us it is still the track of first choice. It’s toy-like, and many of us like it that way. However, if and when the decision is made to add more realism to your layout, you don’t have to leave your tubular track behind.

In building my most recent layout, featured in the November 2013 issue of Classic Toy Trains, I opted to use traditional tubular track in a realistic setting. I used three techniques to blend the track into my layout setting – painting the rails, adding ties, and ballasting. The combination successfully downplayed the traditional shiny and whimsical nature of tubular track. I then used landscape blending to provide a more realistic environment.

Tie up your track
A section of traditional tubular track – either O-27 or standard O – has only three metal ties, and these are twice the width of normally proportioned ties. I opted to place three additional wood ties between each metal tie. In addition, I placed a wood block within the hollow space created by the metal tie. Viewed from the side, you see a complete line of wood edges. Each tie is 1/4 inch tall, 1/2 inch wide, and 2 1/8 inches long.

Not having economical wood material readily available, I took an unconventional route by gluing lengths of ¼-inch-square wood together. I purchased the ¼-inch square wood in 36-inch lengths from a local home-improvement center. A single length netted eight full ties. After gluing two ¼-inch-square lengths together, I lightly sanded the edges and painted the ties with Walmart ColorPlace no. 259863 flat black spray paint. I then used a light coat of common white household glue to hold the ties in place on the cork roadbed.

Dress up your rails
To downplay the shiny tubular rails, I opted to paint the sides of the rails using Floquil no. F110070 Roof Brown. This paint has since been discontinued, but your hobby retailer will be able to steer you to a similar product.

I experimented with a number of techniques, including brush painting, spray-painting, and using paint markers. I highly recommend painting your rails off the layout, before the track is down. In a well-ventilated area you can mask off the black ties and use spray paint; however, you will want to immediately wipe paint off the tops of the rails. I recommend using lacquer thinner to ensure you remove all paint and have clean rail tops.
Another popular choice is the use of Floquil paint markers. I had little success with these, finding the felt marker tips tended to catch on the tabs holding the metal ties in place.

I found the best choice to be brush-painting. Using an old, broad brush, I was able to cover the entire side of the rail in one pass. An additional benefit is the flexibility to go back and paint track already secured to your layout.

With the rails painted, the extra ties inserted and glued in place, and the track secured, it’s time to move on to the finishing touches.

Ballasting your track
Tubular track takes a lot of ballast due to the height of the rails. You want your rails to rest on the ballast and the ballast level to match the tie height. If you need to economize, you can experiment with an inexpensive filler material, such as sawdust, and place a thin layer of ballast over the filler.

There are many commercial products available for ballasting. I used Brennan’s Better Ballast (brennansmodelrr.com) and recommend it highly. The product is well sized and has a good range of coloration.

There are many substitute products used for ballasting, including kitty litter, roofing granules, aquarium gravel, and small pebbles. Think of it this way. Go to a real track and pick up a single piece of ballast. It fits comfortably in your hand. Now equate the size of the O scale ballast you intend to use to the hand of an O scale person. By looking at it from this perspective, you will find many of these substitute products to be just too large. Like most things in model railroading, think of the process as it relates to real life.

So there you have it. If you’re a fan of traditional Lionel track – be it O or O-27 – you can easily bring more realism to your track by following these suggestions.

JOIN THE DISCUSSION

Read and share your comments on this article
COMMENT ON THIS ARTICLE

Want to leave a comment?

Only registered members of ClassicToyTrains.com are allowed to leave comments. Registration is FREE and only takes a couple minutes.

Login or Register now.
0
FREE DOWNLOAD

FREE DOWNLOAD

Learn which classic toy train track works best for your locomotive's power.

FREE EMAIL NEWSLETTER

Get the Classic Toy Trains newsletter delivered to your inbox twice a month

By signing up you may also receive occasional reader surveys and special offers from Classic Toy Trains magazine. Please view our privacy policy